Overview
ABSTRACT
Pressure Equipment (Boilers, Vessels, Piping) must be designed with due protection against overpressure. The most common pressure safety equipment is pressure relief valves. This paper details the procedures for sizing pressure relief valves applicable to pressure equipment in LPG storage and filling centers (commercial butane and propane, liquefied gases). These plants are also classified for environmental protection (ICPE).
Read this article from a comprehensive knowledge base, updated and supplemented with articles reviewed by scientific committees.
Read the articleAUTHOR
-
Serge ABAUZIT : Pressure equipment consulting engineer - Arts and Crafts Engineer - Former head of the pressure vessels department at APAVE, Montpellier, France
INTRODUCTION
Pressure equipment is designed to contain fluids in an enclosure, the safety of which is ensured by the application of :
rules for placing products on the market, specified in the "essential safety requirements" annex to the Pressure Directive 97/23/EC, as well as specific norms and standards;
rules for installation, maintenance and inspection (under the responsibility of the operator); these rules have a regulatory component (decree of March 15, 2000), and a "technical reference framework" component to support the operator's organization.
One of these rules concerns the prevention of the risk of exceeding admissible limits, and in particular the pressure for which the enclosures are designed. In service, stresses in these enclosures must not exceed values that ensure a minimum safety coefficient specified in European regulations and technical reference codes. The most commonly used safety equipment are safety valves.
This article is intended to illustrate the dimensioning of safety valves in a particular field, that of ICPE liquefied petroleum gas (LPG) storage and filling facilities, following on from the article
It covers the following main topics:
regulations applicable to overpressure protection of pressure equipment ;
The main factors that can lead to an increase in the internal pressure of storage tanks and piping at these sites;
valve installation components affecting valve sizing ;
types of overpressure, by vaporization of the liquid phase, or by thermal expansion of a liquid monophase trapped between two closed shut-off devices;
valve sizing in both cases, using examples.
It is designed to provide a basis for :
send prerequisites to a valve supplier, who will have to justify that the characteristics of his offer allow the evacuation of a flow rate at least equal to that calculated;
to place an order.
It's important to remember, however, that satisfactory sizing of a safety device requires the involvement of all the players concerned: operator, pressure equipment manufacturer (boilermaker or pipe fitter), engineering, valve supplier.
Finally, it gives some recommendations on the pitfalls to be avoided in dimensioning.
Exclusive to subscribers. 97% yet to be discovered!
Already subscribed? Log in!
KEYWORDS
Gas liquefied under pressure | Pressure relieve valves | Industrial plants | Plants classified for the environmental protection | Pressure Vessels | LPG Pressure relieve valves sizing
Pressure Relieve Valves Sizing. LPG storage and filling plants
Bibliography
Also in our database
Websites
Legislative texts (French administration website) http://www.legifrance.gouv.fr
INERIS. AIDA regulatory database http://www.ineris.fr/aida
SNCT (Syndicat national de la chaudronnerie et de la tuyauterie) http://www.snct.org
...Standards and norms
- Dispositifs de sécurité pour protection contre les pressions excessives - NF EN ISO 4126-1 à 7 -
- Industries du pétrole, de la pétrochimie et du gaz naturel. Systèmes de dépressurisation et de protection contre les surpressions - NF EN ISO 23251 -
- Soupapes de sécurité pour réservoirs GPL - NF EN 14129 -
- Soupapes de sûreté des réservoirs de gaz de pétrole liquéfié (GPL). Équipement auxiliaire...
Regulations
Decree no. 99-1046 of December 23, 1999 on pressure equipment
Decree of December 21, 1999 on the classification and conformity assessment of pressure equipment
Order of March 15, 2000 on the operation of pressure equipment
BSEI circular no. 06-80 of March 6, 2006 on the conditions for application of the order of March 15, 2000
Arrêté du 2 janvier 2008 relatif aux stockages contenant de plus de 50 tonnes de...
Technical documentation
INERIS BADORIS : Document de synthèse relatif à une barrière technique – Safety valve – 2007
Manual for the storage of propane and butane. Léon Hérenstein – Société du Journal des Usines à Gaz – 1976
Technical documentation from valve manufacturers
Exclusive to subscribers. 97% yet to be discovered!
Already subscribed? Log in!
Article included in this offer
"Safety and risk management"
(
509 articles
)
Updated and enriched with articles validated by our scientific committees
A set of exclusive tools to complement the resources