Overview
ABSTRACT
Due to their lubricating properties, full oils play a role in optimising friction at the tool/material interface during machining. In practical terms, this reduces the mechanical load on the cutting tool and keeps the temperature rise in the cutting zone within a more favourable range. Furthermore, due to their relatively high viscosity, neat oils effectively help to transport chips away from the cutting zone to prevent them from being recycled, for example. All of these characteristics, combined with control over spray and flow rate, help to increase tool life, productivity and machining quality. Full oils also provide effective protection against oxidation caused by air, humidity or temperature variations. This article reviews the design of full oils and their properties so that machinists can select the products best suited to their intended uses.
Read this article from a comprehensive knowledge base, updated and supplemented with articles reviewed by scientific committees.
Read the articleAUTHORS
-
Benoît BROQUERIE : Cutting Fluids Trainer - Process, Nancy, France
-
Julien THIL : Mechanical Engineer – Doctor of Mechanical Engineering and Energy – Cutting/Machinability Expertise, Metz, France
INTRODUCTION
Cutting oils are a key factor in the production of mechanical components through machining. In many situations, given the stringent quality and productivity requirements, cutting oils are an indispensable tool for helping machinists become more competitive. Optimizing the service life of cutting tools through the optimal choice of cutting fluid is also a factor in technical and economic gains. Machined components also benefit from the use of cutting oils, particularly in terms of their durability in service. Although essential, cutting fluids are not always used, and there is at least one scenario in which they are not desirable. Spheroidal graphite cast irons are made of free carbon, which greatly facilitates their machining by acting as a solid lubricant under the effect of the heat generated during the material removal process. Readers are invited to consult article [M 4 611] on spheroidal graphite cast irons.
The term "lubrication" was chosen when machining operations were performed at low cutting speeds. Therefore, to overcome the problem of built-up edge formation occurring at low cutting speeds, neat oil was used to prevent the machined material from welding to the cutting tool. This era is now largely over (except for the example illustrated below), but the term has remained. Although industrial production techniques and technologies have evolved considerably, "fluidic" assistance remains necessary, particularly for chip removal, cooling of the cutting zone, optimization of the friction coefficient, etc.
In doing so, it may now be preferable to refer to "cutting fluid."
To gain the best possible understanding of the content of this article, readers are invited to read the article
Derived from polycyclic aromatic hydrocarbons (PAHs), whole oils mainly have lubricating properties. This property is essential in the context of tool/workpiece friction. Due to their high lubricating power, they reduce the coefficient of friction at the tool/material interface, optimizing the sliding between these two components. As a result, this generates better thermal balance in the cutting zone and reduces abrasion/adhesion wear on the tool. In practical terms, this translates into optimized tool life. An underlying effect is that neat oils also reduce machine energy consumption, thanks to the optimization of the friction coefficient, better heat control in the cutting zone, and slower wear of the cutting tool.
PAHs are chemical contaminants formed as a result of the incomplete combustion of organic products. These molecules are toxic to humans: some PAHs are carcinogenic and genotoxic.
It is the lubricating power of whole oils, not to be confused with the cooling power of soluble oils, for example, that limits the...
Exclusive to subscribers. 97% yet to be discovered!
Already subscribed? Log in!
KEYWORDS
Coolant fluids | neat oils | additives | friction | cutting temperature | chip evacuation
Coolant fluids. Neat oils
Bibliography
- (1) - BIERLA (A.) - Usinage des aciers prétraités à l'huile entière – Effets physico-chimiques des additifs soufrés. - Thèse de doctorat de l'École Nationale Supérieure d'Arts et Métiers, spécialité Génie mécanique – Procédés de fabrication (2009).
- (2) - THIL (J.) - Fabrication soustractive métallique – Coupe des matériaux...
Also in our database
Standards and norms
- Petroleum products and lubricants – Determination of the UV absorption index of the DMSO extract of whole cutting oils - NF T60-607 - Mai 1998
- Petroleum products – Determination of the flow point – In force, mandatory standard - NF T60-105 - Décembre 1996
- Standard Test Method for Pour Point of Petroleum Products – Active - ASTM D97-17b - 2022
- Petroleum and related products of natural or synthetic...
Regulations
Labor Code, Articles 4121-2, R. 4412-1 to R. 4412-57.
Environmental Code, Article L. 541-10-1 (amended).
Regulation (EC) No. 1272/2008 of the European Parliament and of the Council of December 16, 2008 on classification, labeling, and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC and amending Regulation (EC) No. 1907/2006, OJEU of December 31, 2008, p. 1–1355.
Law...
Directory
Manufacturers – Suppliers – Distributors (non-exhaustive list)
BLASER: https://blaser.com
CASTROL: https://www.castrol.com
FUCHS: https://www.fuchs.com
IGOL: https://www.igol.com
...Exclusive to subscribers. 97% yet to be discovered!
Already subscribed? Log in!
Article included in this offer
"Material processing - Assembly"
(
188 articles
)
Updated and enriched with articles validated by our scientific committees
A set of exclusive tools to complement the resources